A new decal kit is perhaps the most affordable way to make your bike look like new again. 24MX Atebe also ensures that you maintain your original style!
The model name of the radiator wings is adapted to your chosen model. For example, if you buy a KTM 250 SX, it will say “SX”.
The decal kit consists of the following parts:
• Radiator shrouds
• Tank (depending on model)
• Front fender
• Rear fender
• Fork leg protection
• Number plate
• Side panels/Air can
• Swingarm
N.B: Decal kits cannot be returned or exchanged.
IMPORTANT! If your decal kit contains a tank decal, it must be perforated! Otherwise, there is a high risk that air bubbles will form due to petrol fumes. This is easily done with a razor blade BEFORE mounting.
Please note that you cannot exactly match the colours of the decals with the colour of the original plastics.
The decals are manufactured in our own state-of-the-art printing plant and are of the highest quality.
After the decal has been printed with digital printing, it is laminated with a very strong and transparent plastic material that protects against wear.
After this, an acrylate-based glue is applied which sticks the decals down while keeping them removable without leaving glue residue on the plastic.
Installation of decal kit:
Be sure to clean your plastic thoroughly first. Pre-decal cleaner gives the best results but brake clean also works.
This also applies to new plastics, which have oil residues on the surface after manufacture.
The decals should be mounted at room temperature.
Make sure that the decal is well centered on the plastic before you start pasting it. When you are satisfied with the fit, remove the protective film from one corner of the decal and then start to press the decal down firmly.
It is good to have a small cloth/sponge to press down with that easily slides over the decal.
Carefully move forward in straight lines as you press down gently to avoid air bubbles.
For the curved/shaped decals, you can heat the decal gently with a hair dryer/heat gun to make it more pliable.
After mounting, allow the plastic to rest for 24 hours at room temperature before riding to ensure the decals are properly attached.
The model name of the radiator wings is adapted to your chosen model. For example, if you buy a KTM 250 SX, it will say “SX”.
The decal kit consists of the following parts:
• Radiator shrouds
• Tank (depending on model)
• Front fender
• Rear fender
• Fork leg protection
• Number plate
• Side panels/Air can
• Swingarm
N.B: Decal kits cannot be returned or exchanged.
IMPORTANT! If your decal kit contains a tank decal, it must be perforated! Otherwise, there is a high risk that air bubbles will form due to petrol fumes. This is easily done with a razor blade BEFORE mounting.
Please note that you cannot exactly match the colours of the decals with the colour of the original plastics.
The decals are manufactured in our own state-of-the-art printing plant and are of the highest quality.
After the decal has been printed with digital printing, it is laminated with a very strong and transparent plastic material that protects against wear.
After this, an acrylate-based glue is applied which sticks the decals down while keeping them removable without leaving glue residue on the plastic.
Installation of decal kit:
Be sure to clean your plastic thoroughly first. Pre-decal cleaner gives the best results but brake clean also works.
This also applies to new plastics, which have oil residues on the surface after manufacture.
The decals should be mounted at room temperature.
Make sure that the decal is well centered on the plastic before you start pasting it. When you are satisfied with the fit, remove the protective film from one corner of the decal and then start to press the decal down firmly.
It is good to have a small cloth/sponge to press down with that easily slides over the decal.
Carefully move forward in straight lines as you press down gently to avoid air bubbles.
For the curved/shaped decals, you can heat the decal gently with a hair dryer/heat gun to make it more pliable.
After mounting, allow the plastic to rest for 24 hours at room temperature before riding to ensure the decals are properly attached.